How to Upgrade to Fedora 37 from Fedora 36 Workstation (GUI and CLI Method)

3 min


Complete steps to upgrade to Fedora 37 from Fedora 36 workstation edition with GUI and CLI method.

Fedora 37 release is finally out after a series of delays. This iconic release brings stunning GNOME 43, the latest Kernel 6.0, KDE Plasma 5.26, Wayland updates and more. You can read my guide on Fedora 37 features on this page.

If you’re trying to upgrade to Fedora 37 from Fedora 36, here are the recommended steps you should follow.

Note: If you are running Fedora 37 beta version, you do not need to follow the below steps to upgrade. You can run sudo dnf update && sudo dnf upgrade from the terminal to get this version.

If you are running an older version of Fedora, such as 35 or 34, you should not skip versions to upgrade directly to 37. You can either do a step upgrade to 36 and then 37; Or do a clean installation. In my experience, several apps and extensions break if you skip versions during upgrades, including Kernel-related problems.

Upgrade to Fedora 37

Before you jump into the update, here are a few housekeeping you should do. In case you run into problems. It’s always recommended.

Steps to Follow before upgrading to Fedora 37

Firstly, Open GNOME Software and check for any pending updates. Or, open a terminal and run the following command to ensure that your system is up-to-date.

sudo dnf update

After completing the above command, reboot your system to ensure all the updates are applied.

Secondly, take backups of your important documents such as pictures, docs or videos from your home directory to a safe place (perhaps a separate partition or USB stick). The Fedora upgrade process never fails, but if you use NVIDIA or any specific hardware with a dual boot system, I recommend you take backups.

Third, install the Extensions Flatpak application and disable all the GNOME Extensions (for the GNOME desktop). The primary reason is not all the extensions are ported yet to GNOME 43. Hence it is safe to disable all of them before upgrading. And you can enable them later after you complete the upgrade process.

Moreover, look at the official forum for any ongoing major bugs of Fedora 37 that may impact the upgrade process. Don’t spend much time on this.

Finally, the upgrade process takes some time (in hours), so ensure you have sufficient time and a stable internet connection.

How to Upgrade to Fedora 37 Workstation

Graphical Method (GUI)

After the official release of Fedora 37, you should see a prompt in GNOME Software showing that an upgrade is available. If you do not see any prompt, don’t worry. Wait for a day or two, and you should have it.

Also, you can visit the Updates tab in GNOME Software and see if it is available.

Click on the notification and hit Download to start the upgrade process. The upgrader will download the required packages and prompt you to restart. Hit restart to continue the upgrade process.

Fedora will apply the upgrades during reboot.

Command-Line method (CLI)

If you are comfortable with the command line, you can use the dnf upgrade command to perform the upgrade process.

Open up the terminal and run the below command:

sudo dnf upgrade --refresh

This command will refresh the new upgrade stream’s packages to prepare for Fedora 37.

Next, install the dnf upgrade plugin by running the below command. This is required for the upgrade process.

sudo dnf install dnf-plugin-system-upgrade

Ensure your system is up-to-date by running the below command and installing any necessary pending updates. Do it once again (if you have done it via pre-upgrade steps)

sudo dnf --refresh upgrade

Initiate the download process by running the below command. This command will fetch all required packages and save them locally before upgrading.

sudo dnf system-upgrade download --releasever=37

If you installed many packages and applications manually and are unsure whether they are correctly supported by Fedora 37, run the above command with “–allowerasing” flag. When you provide this, dnf will remove the blocker packages for your system upgrade.

The above command displays what will be replaced, updated, upgraded, or downgraded. Carefully glance through the list if you want to review the list. Or, you can check the red-marked items and start the upgrade process like the below image.

Fedora 37 upgrade process - image 1
Fedora 37 upgrade process – image 1
Downloading Fedora 37 upgradable packages
Downloading Fedora 37 upgradable packages

Remember, the download size ideally is in GB, so that it might take some time based on your internet speed.

After the above command is complete, run the below command to start the upgrade.

sudo dnf system-upgrade reboot

The system will reboot automatically and wait until the entire upgrade process completes. As I mentioned earlier, this might take time in terms of hours, depending on your system hardware. Hence be patient.

If all goes well, you will be greeted with a brand new Fedora 37 system.

All the best! 🤞


Arindam

Creator of debugpoint.com. All time Linux user and open-source supporter. Connect with me via Telegram, Twitter, LinkedIn, or send us an email.
Subscribe
Notify of
guest

This site uses Akismet to reduce spam. Learn how your comment data is processed.

0 Comments
Inline Feedbacks
View all comments
0
Would love your thoughts, please comment.x
()
x